Automotive

Variable Normal Load Friction and Wear Measurement System
TYPE:HHS2000S/ HHS3000S
A More Advanced Type of Wear Tester has been Realized
In this instrument, for a single measurement of test paper strip, it is possible to create 3-dimensional wear condition graphs showing the relationships between the number of wear movements, vertical loading, friction and wear volumes, and to determine the critical loading responding to wear transitions. Accordingly, not only will it be unnecessary to have multiple test pieces, but the testing time will also be greatly shortened and the requirement for troublesome data analysis can be eliminated, allowing excellent data to be obtained.
Friction wear tester
TYPE: 40
Standard model of new friction and wear tester
Hop-up type acrylic cover that can be covered during measurement, newly developed orthogonal balance arm method, etc.
The birth of a new generation standard model of Tribo Gear.
Equipped with a Y-direction stage as standard, making testing easier.
Perform friction and wear tests comfortably with the Tribo Gear TYPE 40, which is easier to use and more accurate.
Portable Friction Meter Muse
TYPE:37i
Measurements by Anyone, Anywhere
The Muse Type: 94i-IIis a portable measuring instrument that can easily be used by anyone to measure the static friction coefficient between objects.
Previously, methods of measuring static friction generally used incline methods and strain gages, and their use was limited to locations such as laboratories. The inability to make measurements on-site was a weak point of these methods.
This unique instrument is offered as a “new static friction measurement method” that solves all of the above problems at once.

Tactile Meter
TYPE:33
Expressing Sensory Evaluation in Numerical Values
This instrument allows texture, feeling, and blending, which were previously difficult to quantify, to be shown numerically.
Using three strain gages, the resistances in the X, Y and Z directions is detected.
Operation only requires placing the sample on the test piece table and tracing the object with your finger or other object. Measurement can be easily carried out.
In addition, using the handy probe, samples that can not be loaded on the test piece table can also be measured.
Surface Property Tester
TYPE:14FW
Supports a Variety of Research Topics
A DC servo motor (FW type) permits a linear movement of the mobile base when loaded with a test piece.
The resistance transmission mechanism, consisting of the vertical arm and horizontal arm with two fulcrums, conveys the resistance received from each adapter to the detector of the load converter.
A zero balancer is provided at one end of the horizontal arm to balance the dead weight of each adapter so that the vertical loading becomes zero.
In addition, at the other end of the arm there is an adaptor holder, and directly above this there is a weight pan on which weights up to 1000g can be applied.
The detected resistance is amplified by the dynamic strain amplifier and can be output to each recorder.
An easy to use touch panel has been utilized in the operation and display units.
Portable Friction Meter Muse
TYPE:94i-II
Measurements by Anyone, Anywhere
The Muse Type: 94i-IIis a portable measuring instrument that can easily be used by anyone to measure the static friction coefficient between objects.
Previously, methods of measuring static friction generally used incline methods and strain gages, and their use was limited to locations such as laboratories. The inability to make measurements on-site was a weak point of these methods.
This unique instrument is offered as a “new static friction measurement method” that solves all of the above problems at once.

Both-Way Wear Tester
TYPE:30/30S
The Simplest Both-Way Wear Tester
This tester is focused on wear testing evaluation by visual inspection. The Basic Grade Type: 30, and the Type: 30S with non-staged high speed adjustment function and specified rotation number auto stop function, are available.
In addition, the 2-series and 4-series specifications, in which testing can be carried out a number of times under the same conditions, are also available.

Torque Type Friction and Wear Tester
TYPE:20
Disk-on-disk and Ball-on-disk Friction and Wear Testing
The torque converter is directly connected to the turntable on which the test piece can be mounted.
For the loading, it will be possible to select the disk for surface contact and the ball indenter for point contact.
Because the disk and the ball indenter can both be balanced using the dead weight, low loading can be used to carry out highly accurate friction and wear testing.

Continuous Loading Surface Property Tester
TYPE:22
Evaluates Film Adhesion from the Scratch Resistance caused by Continuous Loading
Using two pulse motors, the mobile base that is loaded with the test piece and the continuous loading weight guide are moved simultaneously.
In order to rotate the arm to which the scratching needle is attached, it is possible to proportionally increase the vertical loading of the continuous loading weights on the scratching needle test piece as the test piece travels.
In addition, the scratching needle mounting part incorporates a load converter that detects the resistance. From the friction resistance in the low loading range, minute changes in the scratching resistance and peeling resistance can be directly detected.
In the friction and wear test, by carrying out both-way operation of the test piece under fixed loading conditions, the friction resistance can be detected from the ball indenter.

Continuous Loading Scratching Intensity Tester
TYPE:18/18L
Indicates Scratch Resistance in Numerical Values using Continuous Loading
onical scratch needles are used, which have R-processed tips (various types between 0.005-1.0mm). As the mobile base loaded with the test piece travels, continuous loading is applied to the scratching needle by the weight rolling on the arm.
The travel distance is 100mm, and by replacing the continuous loading weight it is possible to select 0-50g, 0-100g, or 0-200g.
For example, by adding the 0-200g continuous loading weights to the 100g fixed loading weight that is already loaded, it is possible to obtain 100-300g loading.
Due to the use of a mechanical continuous loading device, troublesome calibration will not be required. Highly reproducible testing can always be carried out.
By using only the fixed loading weight without the continuous loading weights, the scratching hardness can also be obtained.

For catalog requests and product inquiries,
please contact us using the inquiry form.