Reciprocating Wear

A More Advanced Type of Wear Tester has been Realized
In this instrument, for a single measurement of test paper strip, it is possible to create 3-dimensional wear condition graphs showing the relationships between the number of wear movements, vertical loading, friction and wear volumes, and to determine the critical loading responding to wear transitions. Accordingly, not only will it be unnecessary to have multiple test pieces, but the testing time will also be greatly shortened and the requirement for troublesome data analysis can be eliminated, allowing excellent data to be obtained.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

Standard model of new friction and wear tester
Hop-up type acrylic cover that can be covered during measurement, newly developed orthogonal balance arm method, etc.
The birth of a new generation standard model of Tribo Gear.
Equipped with a Y-direction stage as standard, making testing easier.
Perform friction and wear tests comfortably with the Tribo Gear TYPE 40, which is easier to use and more accurate.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

Supports a Variety of Research Topics
A DC servo motor (FW type) permits a linear movement of the mobile base when loaded with a test piece.
The resistance transmission mechanism, consisting of the vertical arm and horizontal arm with two fulcrums, conveys the resistance received from each adapter to the detector of the load converter.
A zero balancer is provided at one end of the horizontal arm to balance the dead weight of each adapter so that the vertical loading becomes zero.
In addition, at the other end of the arm there is an adaptor holder, and directly above this there is a weight pan on which weights up to 1000g can be applied.
The detected resistance is amplified by the dynamic strain amplifier and can be output to each recorder.
An easy to use touch panel has been utilized in the operation and display units.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

The Simplest Both-Way Wear Tester
This tester is focused on wear testing evaluation by visual inspection. The Basic Grade Type: 30, and the Type: 30S with non-staged high speed adjustment function and specified rotation number auto stop function, are available.
In addition, the 2-series and 4-series specifications, in which testing can be carried out a number of times under the same conditions, are also available.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

TYPE:38F is the steel wool durability tester developed by HEIDON, designed for JIS K 7317:2022 (Plastics — Determination of scratch hardness of specialty films) and other surface durability evaluations.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

TYPE:38P is the hard coat evaluation tester developed by HEIDON for measuring the scratch resistance and surface durability of hard-coated films and panels.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

Two Types of Testing in One Instrument! Both-way Sliding Testing and Rotating Drum Testing
This friction and wear tester allows not only the same sliding testing as that offered by TriboStation, but also enables rotating drum testing. Adding to the same sliding testing that was possible with previous friction and wear testers, rotation drum testing can also be carried out.

The friction and wear tester provides two functions in the same machine, so that testing of photosensitive drums and supply paper rollers can be measured with the same rotation used under the actual measurement conditions, while paper and plate-shaped samples can be measured by straight line both-way sliding testing.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.

Birth of a high-performance, low-cost friction and wear tester.
We have reduced costs as much as possible while maintaining the measurement performance of friction gears.
The basic performance is comparable to high-end models such as touch panel operation and various measurement ranges.
A load converter with an integrated stylus holder has been adopted to further improve operability.
Tribosoft (optional) makes it easy to measure, analyze, and manage from measuring the coefficient of static friction to measuring reciprocating wear.

Power supply: 100 V AC only. A step-down transformer is required for use outside Japan.